Nie-Tech Co., Ltd.

Z-Wave- Produkte, Smart-Home- System, IP-Kamera Hersteller / Lieferant in China.

Startseite Unternehmensprofil Produktliste Kontakt Anfrage Senden
Startseite> Produktliste> Infrarot-Sensor> Drahtloser Bewegungs-Sensor EVA-Logik (ZW112)

Drahtloser Bewegungs-Sensor EVA-Logik (ZW112)

Referenz FOB Preis:
US $ 20,00- 32,31  / Stück
Zahlungsbedingungen: LC, T / T, D / P, PayPal, Klein-Betrag Zahlung, Western Union
Produktionskapazität: 3000PCS/Month
Verpackung: Neutral Packing / Depends on Customer's Reqirest

Produktbeschreibung

Basis Info
  • Modell Nr.: ZW112
  • Funktion Typ : Infrarotbereich und Kommunikationssystem
  • Erfassungstyp : Wärmemelder
  • Ausgangssignaltyp : Analog Typ
  • Fertigungsprozess : Injektion
  • Material : Kunststoff
  • IP-Schutzklassen : IP55
  • Bescheinigung : CE
  • Kundenspezifische : Kundenspezifische
Zusätzliche Informationen..
  • Trademark: EVA LOGIK
  • Packing: Neutral Packing / Depends on Customer's Reqirest
  • Standard: SGS, ROHS, CE
  • Origin: Dongguan, China
  • HS Code: 8504500000
  • Production Capacity: 3000PCS/Month
Produktbeschreibung

ZW112   PIR Sensor     Technical data Installation Introduction This sensor is a Z-Wave enabled device (interoperable, two-way RF mesh networking technology) and is fully compatible with any Z-Wave enabled network.  Technical data *Operation area: 12m,100°*Low battery detection*Tamper Switch*Range: 30m line of sight*Operating temp: -15oC~40oC*Working Voltage: 3V* Battery: CR123A *1pc*Dimensions: 91.5*61.5*48MM*Frequency: 868.4MHz/865.2MHz/869.2MHz/908.4MHz/921.4MHz  Installation 1. Release cover tab to open the cover. 2. Insert a CR123A battery into the battery compartment, and LED will start to flash slowly, which means the sensor has not yet been "inclusion". 3. Close the cover back to sensor. 4. For "Add" in (adding to): Put the Z-Wave Interface Controller into "Add" mode, and following its instruction to add the ZW112 to your controller. To get in the "Add" mode, the distance between sensor and controller is suggested to be in one meter. Press the learn switch of ZW112 once. The LED on the ZW112 should stop flashing, if not, please try again. For "Remove" from (removing from) a network: Put the Z-Wave Interface Controller into "Remove" mode, and following its instruction to delete the ZW112 to your controller. Press the learn switch of ZW112 once to be excluded. The LED on the ZW112 should start to flash. For "Group": removing the cover of the ZW112 to get into "Awake" mode, then put the Z-Wave  Interface Controller into "Group", and following its instruction to associate the ZW112 with other device. Close the cover back after "Group" done, afterward the ZW112 will get into "Sleep" mode for power saving. Support one association group (5 nodes). Note: "Awake" mode: it is to leave the "Sleep" mode by removing the cover of ZW112, to allow the Z-Wave Interface Controller to do "Group. 5. Using gum wall plug & screws to mount ZW112 at 2 meters above surface. To enhance proper operation, place ZW112 on the angle which can detect the room widely. The solid area means the detector's coverage range.  Safety and maintenance instruction-       Make sure that all electric connections and connection cables meet the pertaining regulations and are in conformity with the operating instruction.-       Do not overload electrical outlets or extension cords, fire or electric shocks can be the result.-       Please contact an expert in case you have any doubts about the mode of operation, the safety or connecting the appliances.-       Keep all parts away from young children's reach.-       Do not store this item on wet, very cold or warm places, this can damage the electronic circuit boards.-       Avoid dropping or shocks, this can damage the electronic boards.-       Never replace damaged power cables yourself! In such case, remove them from the net and take the devices to a workshop.-      Wireless system are subject to interference from cordless phones, microwaves, and other wireless devices during installation and operation. MaintenanceThe devices are maintenance-free, so never open them. The guarantee becomes void when you open the appliance. Only clean the outside of the devices with a soft, dry cloth or a brush. Prior to cleaning, remove the devices from all voltage sources. NOTEDo not use any carboxylic cleaning agents or petrol, alcohol or similar. These will attack the surface of devices. Besides, the vapors are hazardous to your health and explosive. Do not use any sharp edged tools, screw drivers, metal brushes or similar for cleaning. Warranty 1 year