Grundlegende Informationen.
The Number of Rows
Single
Material
Low Carbon Steel
Spherical
Non-Aligning Bearings
Load Direction
Radial Bearing
Produktbeschreibung
Descriptions
R&B bearings will support you to spot the difference in the example of HF 101612 and FC 10 as follows:
1: HF is flat end needle roller; while FC is pointed end needle roller;
2: HF is light series, while FC is heavy duty series one way bearing. It means FC will have higher torque rating than HF, which is the most important factor for one way bearing.
3: There is only one needle roller in each cage window for HF one way bearing; while multi-roller in each cage window for FC one way bearing.
4: Single roller per stainless steel spring for HF one way bearing; while multi-roller per stainless steel spring for FC one way bearing.
one-way needle roller bearing
HFL series drawn cup one-way needle roller bearing has two supporting needle bearing and one roller clutch which shares a punching outer ring, and can be used as a special space-saving support. The two supporting bearing are assembled on both sides of the roller clutch, and endure the radial load. The supporting needle bearing is composed of plastic cage and needles.
Main features: the unidirectional movement, reverse lock; the high conversion frequency and high conversion accuracy.
SPECIAL NOTES
? HFL series has two integral radial bearings arranged on both sides of needle roller clutch. They can therefore support radial forces in particularly space-saving bearing arrangements.
? Plastic springs (HFL...KF) are available for some sizes.
? Partially knurled outer ring (HFL...R) is available upon request.
? A special tool is suggested when assembling the clutch and bearing assembly. For details please contact our engineers.
? Only after the clutch and bearing assembly has been pressed into the hole of the housing, the drawn thin-walled outer ring could then obtain its final dimension and geometric accuracy.
? The transmissible torque and the stresses which can be taken by the housing are subject to the material and the wall thickness of the housing, and such data is needed upon enquiry.
? The clutch and bearing assembly can be normally used in temperature range from -30°C to 120°C. For the working environment above 70°C, oil lubrication is recommended.
Specification:
Fw=inner diameter D=outer diameter C=height
Shaft Diameter | Clutch Designation | Mass Approx | Borndary Dimensions | Torgue Ma | 1 Limiting Speed | Suitable Drawn Cup Bearings |
Plastic Springs | Steel Springs | Fw | D | C | Rotating Shaft Min-1 | Rotatng Outer Ring Min-1 |
mm | g | mm | Nm | rpm |
HF ( INA/ ) |
3 | HF0306KF | | 0.9 | 3 | 6.5 | 6 | 0.2 | 36000 | 7000 | HK0306TN |
4 | HF0406KF | -- | 1 | 4 | 8 | 6 | 0.34 | 34000 | 8000 | HK0408TN |
HF0406KFR | -- | 1 | 4 | 8 | 6 | 0.1 | 34000 | 8000 | HK0408TN |
6 | HF0608KF | | 2.8 | 6 | 10 | 8 | 1.5 | 20000 | 11000 | HK0608 |
HF0612KF | HF0612 | 3 | 6 | 10 | 12 | 1.76 | 23000 | 13000 | HK0608 |
HF0612KFR | HF0612R | 3 | 6 | 10 | 12 | 1.76 | 23000 | 13000 | HK0608 |
| HF061210 | 3.5 | 6 | 12 | 10 | 3 | 20000 | 13000 | HK061208 |
8 | HF0812KF | HF0812 | 3.5 | 8 | 12 | 12 | 3.15 | 17000 | 12000 | HK0808 |
HF0812KFR | HF0812R | 3.5 | 8 | 12 | 12 | 4 | 17000 | 12000 | HK0808 |
-- | HF061210 | 3.2 | 8 | 12 | 10 | 3 | 16000 | 12000 | HK0808 |
-- | HF081410 | 3.6 | 8 | 14 | 10 | 4.6 | 15000 | 11000 | HK081410 |
-- | HF081610 | 4.1 | 8 | 16 | 10 | 5.5 | 15000 | 11000 | HK081610 |
-- | HF081412 | 4 | 8 | 14 | 12 | 5 | 16000 | 12000 | HK081410 |
10 | HF1012KF | HF1012 | 4 | 10 | 14 | 12 | 5.3 | 14000 | 11000 | HK1010 |
HF1012KFR | HF1012R | 4 | 10 | 14 | 12 | 1.5 | 14000 | 11000 | HK1010 |
12 | -- | HF1216 | 11 | 12 | 18 | 16 | 12.2 | 11000 | 8000 | HK1212 |
14 | -- | HF1416 | 13 | 14 | 20 | 16 | 17.3 | 9500 | 8000 | HK1412 |
16 | -- | HF1616 | 14 | 16 | 22 | 16 | 20.5 | 8500 | 7500 | HK1612 |
18 | -- | HF1816 | 16 | 18 | 24 | 16 | 24.1 | 7500 | 7500 | HK1812 |
20 | -- | HF2016 | 17 | 20 | 26 | 16 | 28.5 | 7000 | 6500 | HK2010 |
| | HF2216 | 25 | 22 | 28 | 16 | 32 | 6500 | 6000 | |
25 | -- | HF2520 | 30 | 25 | 32 | 20 | 66 | 5500 | 5500 | HK2512 |
| | HF273420 | 30 | 27 | 34 | 20 | 110 | | | |
| | HF404725 | 45 | 40 | 47 | 25 | 185 | | | |
| | HF485620 | 43 | 48 | 56 | 20 | 230 | | | |
| | HF586820 | 86 | 58 | 68 | 20 | 320 | | | |
30 | -- | HF3020 | 36 | 30 | 37 | 20 | 90 | 4500 | 4500 | HK3012 |
35 | -- | HF3520 | 40 | 35 | 42 | 20 | 121 | 3900 | 3900 | HK3512 |
Shaft Diameter | Clutch Designation | Mass Approx | Borndary Dimensions | Torgue Ma | 1 Limiting Speed | Suitable Drawn Cup Bearings | Plastic Springs | Steel Springs | Fw | D | C | Rotating Shaft Min-1 | Rotatng Outer Ring Min-1 | mm | g | mm | Nm | rpm | HF ( INA/ ) | 3 | HF0306KF | | 0.9 | 3 | 6.5 | 6 | 0.2 | 36000 | 7000 | HK0306TN | 4 | HF0406KF | -- | 1 | 4 | 8 | 6 | 0.34 | 34000 | 8000 | HK0408TN | HF0406KFR | -- | 1 | 4 | 8 | 6 | 0.1 | 34000 | 8000 | HK0408TN | 6 | HF0608KF | | 2.8 | 6 | 10 | 8 | 1.5 | 20000 | 11000 | HK0608 | HF0612KF | HF0612 | 3 | 6 | 10 | 12 | 1.76 | 23000 | 13000 | HK0608 | HF0612KFR | HF0612R | 3 | 6 | 10 | 12 | 1.76 | 23000 | 13000 | HK0608 | | HF061210 | 3.5 | 6 | 12 | 10 | 3 | 20000 | 13000 | HK061208 | 8 | HF0812KF | HF0812 | 3.5 | 8 | 12 | 12 | 3.15 | 17000 | 12000 | HK0808 | HF0812KFR | HF0812R | 3.5 | 8 | 12 | 12 | 4 | 17000 | 12000 | HK0808 | -- | HF061210 | 3.2 | 8 | 12 | 10 | 3 | 16000 | 12000 | HK0808 | -- | HF081410 | 3.6 | 8 | 14 | 10 | 4.6 | 15000 | 11000 | HK081410 | -- | HF081610 | 4.1 | 8 | 16 | 10 | 5.5 | 15000 | 11000 | HK081610 | -- | HF081412 | 4 | 8 | 14 | 12 | 5 | 16000 | 12000 | HK081410 | 10 | HF1012KF | HF1012 | 4 | 10 | 14 | 12 | 5.3 | 14000 | 11000 | HK1010 | HF1012KFR | HF1012R | 4 | 10 | 14 | 12 | 1.5 | 14000 | 11000 | HK1010 | 12 | -- | HF1216 | 11 | 12 | 18 | 16 | 12.2 | 11000 | 8000 | HK1212 | 14 | -- | HF1416 | 13 | 14 | 20 | 16 | 17.3 | 9500 | 8000 | HK1412 | 16 | -- | HF1616 | 14 | 16 | 22 | 16 | 20.5 | 8500 | 7500 | HK1612 | 18 | -- | HF1816 | 16 | 18 | 24 | 16 | 24.1 | 7500 | 7500 | HK1812 | 20 | -- | HF2016 | 17 | 20 | 26 | 16 | 28.5 | 7000 | 6500 | HK2010 | | | HF2216 | 25 | 22 | 28 | 16 | 32 | 6500 | 6000 | | 25 | -- | HF2520 | 30 | 25 | 32 | 20 | 66 | 5500 | 5500 | HK2512 | | | HF273420 | 30 | 27 | 34 | 20 | 110 | | | | | | HF404725 | 45 | 40 | 47 | 25 | 185 | | | | | | HF485620 | 43 | 48 | 56 | 20 | 230 | | | | | | HF586820 | 86 | 58 | 68 | 20 | 320 | | | | 30 | -- | HF3020 | 36 | 30 | 37 | 20 | 90 | 4500 | 4500 | HK3012 | 35 | -- | HF3520 | 40 | 35 | 42 | 20 | 121 | 3900 | 3900 | HK3512 |
1:;KF,KF; 2:R;
Shaft Diameter | Clutch Designation | Mass Approx | Borndary Dimensions | Torgue Ma | 1 Limiting Speed | Basic Load Ratings | Plastic Springs | Steel Springs | Fw | D | C | Rotating Shaft Min-1 | Rotatng Outer Ring Min-1 | C | Co | KN | mm | g | mm | Nm | rpm | HFL ( INA/ ) | 3 | HFL0308 | -- | 3 | 3 | 3.6 | 8 | 1 | -- | -- | -- | -- | 4 | HFL0408 | -- | 3.5 | 4 | 8 | 8 | 1.5 | -- | -- | -- | -- | 6 | HFL0615KF | HFK0615 | 4 | 6 | 10 | 15 | 1.76 | 23000 | 13000 | -- | -- | HFL0615KFR | HFL0615R | 4 | 6 | 10 | 15 | 0.5 | 23000 | 13000 | -- | -- | -- | HFL061012K | 5 | 6 | 10 | 12 | -- | 21000 | 12000 | -- | -- | 8 | -- | HFL081212K | 6 | 8 | 12 | 12 | -- | 20000 | 12000 | -- | -- | -- | HFL081412K | 7 | 8 | 14 | 12 | -- | 19000 | 12000 | -- | -- | HFL0822KF | HFL0822 | 7 | 8 | 12 | 22 | 3.15 | 17000 | 12000 | 4.05 | 4.15 | HFL0822KFR | HFL0822R | 7 | 8 | 12 | 22 | 1 | 17000 | 12000 | -- | -- | 10 | HFL1022KF | HFL1022 | 8 | 10 | 14 | 22 | 5.3 | 14000 | 11000 | 4.3 | 4.65 | HFL1022KFR | HFL1022R | 8 | 10 | 14 | 22 | 1.5 | 14000 | 11000 | -- | -- | 12 | -- | HFL1226 | 18 | 12 | 18 | 26 | 12.2 | 11000 | 8000 | 6.3 | 6.5 | 14 | -- | HFL1426 | 20 | 14 | 20 | 26 | 17.3 | 9500 | 8000 | 7.1 | 7.7 | 16 | -- | HFL1626 | 22 | 16 | 22 | 26 | 20.5 | 8500 | 7500 | 7.7 | 9 | 18 | -- | HFL1826 | 25 | 18 | 24 | 26 | 24.1 | 7500 | 7500 | 8.3 | 10.3 | 20 | -- | HFL2026 | 27 | 20 | 26 | 26 | 28.5 | 7000 | 6500 | 8.9 | 11.5 | 25 | -- | HFL2530 | 44 | 25 | 32 | 30 | 66 | 5500 | 5500 | 10.9 | 14.1 | 30 | -- | HFL3030 | 51 | 30 | 37 | 30 | 90 | 4500 | 4500 | 12.6 | 17.6 | 35 | -- | HFL3530 | 58 | 35 | 42 | 30 | 121 | 3900 | 3900 | 13 | 19.3 |
| | | Fw | D | C | | Torrington/ & NSK/ | FC4K | 1 | 4 | 8 | 6 | 0.34 | FC6 | 3 | 6 | 10 | 12 | 1.76 | FC6K | 3 | 6 | 10 | 12 | 1.76 | FC8 | 4 | 8 | 14 | 12 | 5.3 | FCL8K | 3.5 | 8 | 12 | 12 | 5 | FC10 | 4.8 | 10 | 16 | 12 | 6 | FCL10K | 4 | 10 | 14 | 12 | 5.3 | FC12 | 11 | 12 | 18 | 16 | 12.2 | FC14K | 13 | 14 | 20 | 16 | 17.3 | FC16 | 14 | 16 | 22 | 16 | 20.5 | FC20 | 17 | 20 | 26 | 16 | 28.5 | FC25 | 30 | 25 | 32 | 20 | 66 | FC30 | 36 | 30 | 37 | 20 | 90 | FC35 | 40 | 35 | 42 | 20 | 121 | FCB8 | 10 | 14 | 14 | 20 | 5 | FCB10 | 15 | 16 | 16 | 20 | 10 | FCB12 | 18 | 18 | 18 | 26 | 12.2 | FCB16 | 22 | 22 | 22 | 26 | 20.5 | FCB20 | 27 | 26 | 26 | 26 | 28.5 | FCB25 | 44 | 32 | 32 | 30 | 66 | FCB30 | 51 | 37 | 37 | 30 | 90 | FCB35 | 58 | 42 | 42 | 30 | 121 |
| | | Fw | D | C | | Torrington/ & NSK/ | RC02 | 2 | 3.175 | 7.15 | 6.35 | 1.5 | RC040708 | 3.5 | 6.35 | 11.112 | 12.7 | 1.9 | RC040708-FS | 3.5 | 6.35 | 11.112 | 12.7 | 1.9 | RC061008 | 4.7 | 9.525 | 15.875 | 12.7 | 4.83 | RC061008-FC | 4.7 | 9.525 | 15.875 | 12.7 | 4.83 | RC081208 | 9.2 | 12.7 | 19.05 | 12.7 | 7.9 | RC081208-FS | 9.2 | 12.7 | 19.05 | 12.7 | 7.9 | RC101410 | 14.5 | 15.875 | 22.225 | 15.88 | 15.4 | RC101410-FC | 14.5 | 15.875 | 22.225 | 15.88 | 15.4 | RC121610 | 17 | 19.05 | 25.4 | 15.88 | 20.9 | RC121610-FS | 17 | 19.05 | 25.4 | 15.88 | 20.9 | RC162110 | 16.2 | 25.4 | 33.338 | 15.88 | 45 | RC162110-FC | 16.2 | 25.4 | 33.338 | 15.88 | 45 | RCB061014 | 12 | 9.525 | 15.875 | 22.22 | 4.83 | RCB061014-FS | 12 | 9.525 | 15.875 | 22.22 | 4.83 | RCB081214 | 16 | 12.7 | 19.05 | 22.22 | 7.9 | RCB081214-FC | 16 | 12.7 | 19.05 | 22.22 | 7.9 | RCB101416 | 21.3 | 15.875 | 22.225 | 25.4 | 15.4 | RCB101416-FS | 21.3 | 15.875 | 22.225 | 25.4 | 15.4 | RCB121616 | 26.5 | 19.05 | 25.4 | 25.4 | 20.9 | RCB121616-FC | 26.5 | 19.05 | 25.4 | 25.4 | 20.9 | RCB162117 | 44.8 | 25.4 | 33.338 | 26.99 | 45 | RCB162117-FS | 44.8 | 25.4 | 33.338 | 26.99 | 45 |
shaft dia. d | boundary dimensions | torque capacity | Fw | D1 | D2 | B | A | mm | mm | N.m (.) | Kg.cm(.) | 4 | 4 | 8 | 8.4 | 6 | 2.6 | 0.08 | 0.82 | 4 | 8 | 8.4 | 6 | 2.6 | 0.15 | 1.53 | 6 | 6 | 10 | 10.4 | 8 | 2.8 | 0.25 | 2.55 | 6 | 10 | 10.4 | 8 | 2.8 | 0.44 | 4.49 | 6 | 10 | 10.4 | 8 | 2.8 | 0.44 | 4.49 | 6 | 10 | 10.4 | 12 | 2.8 | 0.88 | 8.98 | 8 | 8 | 12 | 12.4 | 9 | 2.6 | 0.49 | 5 | <, ;, TD align=middle> 8 | 12 | 12.4 | 9 | 2.6 | 0.88 | 8.98 | 8 | 14.2 | 15 | 12 | 3.6 | 1.18 | 12.04 | 8 | 14.2 | 15 | 12 | 3.6 | 1.96 | 20 | 8 | 14.2 | 15 | 12 | 3.6 | 1.96 | 20 | 8 | 14.2 | 15 | 14.5 | 3.6 | 2.65 | 27.04 | 10 | 10 | 16 | 17 | 10 | 5 | 1.18 | 12.04 | 10 | 16 | 17 | 10 | 5 | 1.96 | 20 | 10 | 16 | 17 | 12 | 5 | 1.37 | 13.98 | 10 | 16 | 17 | 12 | 5 | 2.35 | 23.98 | 10 | 16 | 17 | 12 | 5 | 2.35 | 23.98 | 12 | 12 | 18 | 19 | 16 | 5.1 | 6.28 | 64.08 |
(1).nA. (2),. ,-0mm~-0.25mm,. |
Parameter list of OWC needle roller bearing
Shaft Dia. | Model | Weight | Size(mm) | Driving Torque |
mm | g | Inner Dia. | Outer Dia. | Height | ( Nm ) |
4 | OWC 410 | 1.8 | 4 | 10 | 5.4 | 2.8 |
5 | OWC 511 | 2 | 5 | 11 | 5.4 | 3.5 |
6 | OWC 612 | 2.3 | 6 | 12 | 5.4 | 5.2 |
8 | OWC 814 | 2.8 | 8 | 14 | 5.4 | 6.1 |
10 | OWC 1016 | 3 | 10 | 16 | 5.4 | 9.5 |
4 | OWC 406 | 1.6 | 4 | 8 | 6 | 2.5 |
4 | OWC 408 | 1.8 | 4 | 8 | 8 | 3.1 |
6 | OWC 612-8.4 | 2.35 | 6 | 12 | 8.4 | 6.8 |
6 | OWC 61407 | 2.1 | 6 | 14 | 7 | 6.6 |
6 | OWC 720 | 2.5 | 6 | 12.7 | 7.5 | 7.3 |
6 | OWC 087 | 2.38 | 6 | 10.2 | 8 | 4.6 |
6 | OWC 178 | 3 | 6 | 10.2 | 15 | 7.3 |
8 | OWC 81607 | 2.6 | 8 | 16 | 7 | 7.5 |
8 | OWC 812 | 3 | 8 | 12.7 | 7.3 | 6.8 |
8 | OWC 816-5.5 | 3.5 | 8 | 16 | 5.5 | 8.2 |
8 | OWC 816-6.2 | 3.8 | 8 | 16 | 6.2 | 8.8 |
10 | OWC 1008 | 3.35 | 10 | 16 | 8 | 9.7 |
10 | OWC 1019 | 8.5 | 10 | 19 | 11 | 19.8 |
17 | OWC 173512 | 22.5 | 17 | 35 | 12 | 78 |
17 | OWC 173516 | 25.5 | 17 | 35 | 16 | 95 |
17 | OWC 203316 | 23 | 20 | 33 | 16 | 108 |
MARKS:NON-STANDARD CAN BE PRODUCED |
Transfer capability:
Under the conditions of using the recommended mounting tolerances, the maximum torque that can be transmitteddepends primarily on the design of the seat shell and the shaft (materials, strength, wall thickness). Only when thewall thickness of the seat shell and its material allowable stress certain requirements, the clutch can transfermoment Md.
Installation:
Should be used the assembly mandrel with Needle roller bearings, needle roller clutch pressure holing hole(installed). When the clutch side of the direction of the arrow relative to the shaft is rotated, the clutch will lock, andtherefore should be noted locking direction before installation.
Lubrication:
HF-drawn cup needle roller clutch in oil and grease lubrication. Lubricated with oil, however, before you can get thebest performance, the standard HF-Drawn Cup Clutch has been filled with lithium grease.
Performance test:
The technical requirements of the test method and the standard circle described with Needle roller bearingsdimensional inspection mandrel used nominal size to take the tolerance zone as the lower limit for the h5 shaftalong the arrow in the opposite direction in the clutch can be locked.
Mounting tolerances:
The technical requirements of the seat shell HF-Needle roller bearings, the axis of the tolerance zone h5, the surfaceroughness Ra0.2m, not less than the hardness of HRC60.
Operating temperature:
HF-drawn cup needle roller clutch lubrication properly can the temperature range of -30 ° C to +120 °C long-running,short-term up to 150 ° C Operating Temperature. Lithium Grease Run
ONE WAY BEARING APPLICATIONS
Paper moving for copiers, fax machines, paper towel dispensers, etc.
Exercise equipment
Appliances
Two-speed gearboxes
Rack indexing drives
Converters, non-return devices and transcendental clutches.
Fishing Reels, RC Cars, RC Helis, RC Engines
INSPECTION OF ONE WAY BEARINGS
Although the outer cup of the clutch is accurately drawn from strip steel, it can go slightly out of round during heat treat. When the assembly is pressed into a ring gage or properly prepared housing of correct size and wall thickness, it becomes round and properly sized. Direct measurement of the outside diameter of a drawn cup assembly is an incorrect procedure. The proper inspection procedure is as follows:
1. Press the assembly into a ring gage of the proper size as given in the tabular data.
2. Gage the bore with the specified plug gages of the proper size, as given in the tables of dimensions.
- The locking plug is rotated to insure lockup when the clutch is operated at low limit shaft and is mounted in a high limit housing strong enough to properly size the clutch.
- The overrun plug is rotated to ensure free over-running when the clutch is operated on a high limit shaft and is mounted in a low limit housing.
- The go plug and no go plug insure proper size of the bearings in the clutch and bearing assemblies.
Die Anschrift:
Changhong West Road 182, Wujin District, Changzhou, Jiangsu, China
Unternehmensart:
Hersteller/Werk
Geschäftsbereich:
Auto, Motor und Zusatz, Industrielle Anlagen und Zusatzteile, Mineralien und Energie, Produktionsmaschinen, Werkzeug
Zertifizierung des Managementsystems:
ISO 9001
Firmenvorstellung:
Changzhou Lisongtai Industrial Motion Technology Co., Ltd, ist ein Hersteller spezialisiert auf die Herstellung von verschiedenen Einweglager, Einwegkupplung, Freilaufkupplung, Nadellager. Mehr als 2000 Standardmodell der Einweglager über 1000 Bezeichnungen von metrischen und Zoll-Serie Nadellager werden regelmäßig hergestellt und weit verbreitet für Motorräder, elektrische und luftbetriebene Werkzeuge, Drucker, Licht-und Textilindustrie, Maschinen, Baumaschinen, Autos LKW und Bürogeräte in nationalen und weltweiten Märkten verwendet. Darüber hinaus werden spezielle Lager entsprechend den Anforderungen der Kunden für verschiedene Anwendungen geliefert. Wir haben unsere Produkte nach Korea, Iran, Türkei, Bulgarien, Rumänien, Russland, Italien, Norwegen, USA, Kanada, Usw.
Was sind wir?
Unsere Fabrik wurde in der wirtschaftlich entwickelten Küstenstadt-Industriegebiet Wujin Changzhou Stadt der Provinz Jiangsu entfernt. Hier Transport ist bequem, Es wird nur eine Stunde nach Shanghai mit dem Zug.
Welche Hauptprodukte werden hergestellt?
Einweglager, Einwegkupplung, Freilaufkupplung, Rückanschläge, Nockenkupplung, Nadellager, Stützrollen- und Kurvenlager, Zylinderrollenlager. Axialkugellager mit Falt-Sitz. Wir haben große Bestände, und wir auch Accpect Herstellung für nicht-Standard-Produkt, Kunden Zeichnung oder Proben.
Was ist unser Vorteil?
Produkt: 1999 begann unser Chef als Ingenieur, Einwegkupplungslager zu entwickeln und zu entwerfen, als er in einer großen Lagerfabrik arbeitete. Bis jetzt haben wir Erfolge zu BB-Serie, MZ-Serie, TFS-Serie, NSS-Serie RSBW-Serie zu entwickeln, die bestätigt werden Reichweite in einem hohen Qualitätsniveau kann mit TSUBAKI Marke von Janpan verglichen werden.
Quliaty entspricht Stieber Kupplung, GMN Kupplung, Ringspann Kupplung, Formspag Kupplung, NSK Kupplung, ect.
Serie GFR, Serie DC, Serie ASNU, Serie NFR, Serie GFK, NF-Serie, AE-Serie, AA-Serie, ect, die bestätigt werden können, erreichen in einem hohen Qualitätsniveau kann mit STIEBER Marke aus Deutschland verglichen werden.
FE-Serie, FP-Serie, FND-Serie, FKN-Serie Einwegkupplungslager, die bestätigt werden, erreichen ein hohes Qualitätsniveau kann im Vergleich mit GMN Marke aus Deutschland.
Unseren Kunden weiterhin den höchsten Servicestandard in unserer Branche zu bieten. Wir wollen an der Spitze der Lagerversorgung und -Konstruktion bleiben und unsere Entwicklung in Richtung neuer Lager fortsetzen.
Fabrikausrüstung: Das Unternehmen besitzt die fortschrittlichste CNC automatische Produktionslinie, automatische Montagelinie und eine Vielzahl von Prüfgeräten. Die von uns hergestellten Lager sind alle geräuscharm, vibrationsarm, reibungsarm, hochpräzise, hochgekapselt, Hohe Drehgeschwindigkeit und lange Lebensdauer.
Qualitätskontrolle: 2011 Wir haben die Zertifizierung des Qualitätsmanagementsystems ISO9001: 2008 erhalten, alle unsere Produkte werden vor mehrmaler Inspektion verschickt. Wir liefern auch detaillierte Zeichnungen und bieten, wenn nötig.
Was ist die Anwendung?
Weit verbreitet in Fördermaschine, Reduzierstück, Hebezeug, Aufzug, Automobil, Haushaltsgeräte, Textilmaschinen, Druckmaschinen, Lebensmittelmaschinen und Minenmaschinen usw.
wo unsere Produkte versalzt wurden?
Unsere Produkte in der ganzen Welt spielen eine wichtige Rolle
in Deutschland, Großbritannien, den Niederlanden, Spanien, Italien,
In Indien, Indonesien, den Philippinen, Thailand,
im Iran, Dubai
in Mexiko,
in den Vereinigten Staaten
"Qualität und Service" müssen Ihre wichtigsten Anliegen, die wir in der Praxis umgesetzt haben, bitte durchsuchen Sie unsere Produktkategorie und lassen Sie uns Ihre Anfragen. Unser Ziel ist es, unsere Kunden mit guter Qualität und den besten wettbewerbsfähigen Preisen zu erfüllen. Mit ausreichender Versorgung, großen Vorrat und bequemen Transport, begrüßen wir herzlich neue Kunden, um uns zu besuchen.